Teknikal na parameter:Grip-d 【Tingnan ang】
Ang GRIP-D ay dalawang-piraso na uri ng pag-aayos ng uri, ay maaaring mailagay sa paglabas ng mga tubo sa lugar na ito, nang walang kinakailangang alisin at ibalik ang mga tubo. This makes it the ideal solution for permanent repairs of pipe joints, cracks etc.
The advantage of GRIP-D repair clamps is that is can befitted to existing pipes in situation, without any need to remove and replacing pipes, GRIP-R pipe repair clamp can repair the pipes that are ageing and corrosive and pipe wall has holes or cracks . When installing it, it only needs pipe clamp to wrap the leakage part and tighten the bolt. Then the installation is finished ideally and reliably.
GRIP-D Teknikal na mga parameter
| Lapad | Bolt | |||||||||||
| Od |  |  | B | C | ||||||||
| （Mm） | （In.） | （Mm） | (mm) | (mm) | (mm) | (mm) | (mm) | (mm) | (Nm) | M | ||
| 180 | 178-182 | 16 | 30 | 204 | 142 | 250 | 75 | 10 ～ 25 | 40 | 60 | M12 × 2 | |
| 200 | 7.874 | 16 | 30 | 224 | 142 | 250 | 75 | 10 ～ 25 | 40 | 60 | ||
| 16 | 30 | 251.1 | 142 | 250 | 75 | 10 ～ 25 | 40 | 60 | ||||
| 250 | 9.843 | 16 | 25 | 282 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | ||
| 267 | 16 | 25 | 299 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | |||
| 273 | 16 | 25 | 305 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | |||
| 304 | 10 | 20 | 336 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | |||
| 10 | 20 | 355.9 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | ||||
| 8.5 | 16 | 387.6 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | ||||
| 377 | 8.5 | 16 | 409 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | |||
| 406.4 | 7.5 | 16 | 438 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | |||
| 18.000 | 452-462 | 6.5 | 12 | 489 | 142 | 250 | 75 | 10 ～ 25 | 40 | 80 | ||
| 508 | 503-513 | 6 | 10 | 540 | 142 | 250 | 75 | 10 ～ 25 | 40 | 120 | M16 × 2 | |
| 22.000 | 5.5 | 10 | 142 | 250 | 75 | 10 ～ 25 | 40 | 160 | ||||
| 24.000 | 5 | 10 | 641.6 | 142 | 250 | 75 | 10 ～ 25 | 40 | 160 | |||
| 711.2 | 28.000 | 4 | 5 | 743.2 | 142 | 250 | 75 | 10 ～ 25 | 40 | 160 | ||
| 762 | 30.000 | 4 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 160 | |||
| 812.8 | 4 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 160 | ||||
| 4 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 160 | |||||
| 1016 | 4 | 5 | 1048 | 142 | 250 | 75 | 10 ～ 25 | 40 | 200 | |||
| 44.000 | 3.5 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 200 | ||||
| 48.000 | 3.5 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 200 | ||||
| 1320.8 | 3 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | ||||
| 3 | 5 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | |||||
| 1524 | 2.5 | 5 | 1556 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | |||
| 64.000 | 2.5 | 5 | 1657.6 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | |||
| 1727.2 | 68.000 | 1722-1732 | 2.5 | 5 | 1759.2 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | |
| 1824-1834 | 2 | 5 | 1860.8 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | |||
| 76.000 | 1925-1935 | 2 | 5 | 1962.4 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | ||
| 2032 | 2 | 5 | 2064 | 142 | 250 | 75 | 10 ～ 25 | 40 | 240 | |||
Pagpili ng materyal na Grip-D
| Materyal / sangkap | V1 | V2 | V3 | V4 | V5 | V6 |
| Pambalot | AISI 304 | AISI 304 | ||||
| Bolts | AISI 304 | AISI 304 | AISI 304 | AISI 4135 | ||
| AISI 304 | AISI 304 | AISI 304 | AISI 4135 | |||
| Anchoring Ring | ||||||
| Strip insert (opsyonal) |
Materyal ng gasket ng goma
| Materyal ng selyo | Saklaw ng temperatura | |
| EPDM | Lahat ng kalidad ng tubig, basurang tubig, hangin, solido at mga produktong kemikal | -30 ℃ hanggang sa+120 ℃ |
| NBR | -30 ℃ Upto+120 ℃ | |
| Mataas na temperatura ng likido, oxygen, osono, tubig at iba pa | -70 ℃ hanggang sa+260 ℃ | |
| Ozon, oxygen, acid, gas, langis at gasolina (may insert na strip) lamang) | 95 ℃ hanggang sa+300 ℃ |